Easy handling, productivity and energy efficiency – Siemens offers an answer to these trends with the SINAMICS G120P series. SINAMICS G120P is an innovative and user-friendly converter series that has been specifically optimized for pump, fan and compressor applications in the industrial environment, but also for tasks in building automation.
SINAMICS G120P offers efficient drive solutions for a wide range of applications. With their easy handling, the drives support the user not only in optimizing existing frequency-controlled drives, but also in converting fixed-speed drives and in retrofitting.
The SINAMICS G120P converter series features advanced hardware and software functions that make a substantial contribution towards saving energy and thus make more careful use of our natural resources.
SINAMICS G120P in degree of protection IP20, PM230 Power Module, frame size FSB
SINAMICS G120P in degree of protection IP20, PM240P-2 Power Module, frame size FSD
SINAMICS G120P in degree of protection IP20, PM330 Power Module, frame size GX
SINAMICS G120P in degree of protection IP20, PM230 Power Module, frame size FSC Push Through (with Control Unit and BOP‑2 operator panel)
SINAMICS G120P in degree of protection IP55, PM230 Power Module, frame size FSB
SINAMICS G120P Cabinet converter cabinet units, versions A and C
A high degree of user-friendliness is one of the main characteristics of the SINAMICS G120P:
SINAMICS G120P offers two basic options for guided parameterization/setting in a target application:
Commissioning simple applications
using application wizards optionally available in the IOP‑2 operator panel 1)
The following wizards are available:
An appropriate connection diagram for the standard wiring can be found in the documentation of the IOP‑2 operator panel.
Commissioning of more demanding applications
using plain text scripts through solution-based dialog prompting in the STARTER commissioning tool
The wizards support setpoint input for process values and setpoint exchanges using timers. They also allow easy integration of technological functions, such as cascade connection or hibernation mode. The connection diagrams for standard wiring that are required for the wizards are also supplied.
The following wizards are available:
1) More information is available on the Internet at
https://support.industry.siemens.com/cs/document/67273266
SINAMICS G120P increases the efficiency and minimizes energy consumption in the complete process chain. The converter has integrated hardware as well as software functions as standard. The main features are:
Optimized converter topology for PM230 Power Modules
Flux reduction
Hibernation mode
High efficiency
1) More information on the CU240E‑2 Control Unit is available in Catalog D 31.1, Chapter SINAMICS G120.
2) The safety functions are only available as from function release FS 04 of the PM330 Power Modules.
SINAMICS G120P is ideally suited to pump applications (centrifugal pumps, oscillating and rotating pumps), fan applications (axial and radial fans) and compressor applications (cooling compressors, air and gas compressors). They are deployed in industrial environments, in the process industry and water industry and in building automation.
SINAMICS G120P is ideally suited for the following applications:
SINAMICS G120P is suitable for use under harsh environmental conditions:
SINAMICS G120P is a modular converter system comprising the following components.
The converter communication interface is defined when selecting the Control Unit (FW V4.5 and higher).
The CU230P-2 Control Unit controls and monitors the Power Module and the connected motor using several different closed-loop control modes that can be selected. It supports communication to a local or central controller as well as to the monitoring equipment, and allows all process-related auxiliary equipment and external components to be connected (sensors, valves, contactors, etc.).
The Power Module is selected depending on the power requirement and the application. State-of-the-art IGBT technology with pulse-width modulation is used for reliable and flexible motor operation. Comprehensive protection functions provide a high degree of protection for the Power Module and the motor.
Power Modules for use in building technology for heating, air conditioning and ventilation applications
The Power Modules in degree of protection IP20 are intended for installation in a control cabinet:
The Power Modules in degree of protection IP55 can be erected as distributed units outside a control cabinet.
Power Modules for use in the water/wastewater sector as well as in industrial applications
The Power Modules in degree of protection IP20 are intended for installation in a control cabinet:
Line voltage 380 V to 480 V 3 AC
Line voltage 500 V to 690 V 3 AC
SINAMICS G120P Cabinet
SINAMICS G120P units rated for outputs of 75 kW and higher are also available in the control cabinet version SINAMICS G120P Cabinet for line voltages of 380 V to 480 V 3 AC and 500 V to 690 V 3 AC.
The operator panel supports user-friendly local commissioning, control and diagnostics and enables complete converter data sets to be pre-parameterized and cloned.
Note regarding PM230 Power Modules in degree of protection IP55/UL Type 12:
It is essential to plug on an operator panel or the blanking cover in order to achieve degree of protection IP55.
1) Additional information is available on the Internet at
https://support.industry.siemens.com/cs/document/67273266
The following line-side power components are available for the SINAMICS G120P converters:
Note:
A line reactor must not be used in combination with a PM230 Power Module.
This section contains recommendations for additional line-side components, such as Siemens fuses and circuit breakers (line-side components must be dimensioned in accordance with IEC standards).
Additional information about the listed fuses and circuit breakers is available in the Catalogs LV 10, IC 10 and IC 10 AO as well as in the Industry Mall.
The following DC link components are available for the SINAMICS G120P converters:
Various load-side power components are available for the SINAMICS G120P converters. These allow the use of longer shielded motor cables and increase the motor service life:
Functions specific to pumps, fans and compressors are already integrated, e.g.:
Functions especially for building technology as well as heating/air conditioning/ventilation applications
The following electronic configuring guides and engineering tools are available for SINAMICS G120P converters:
Use SinaSave to calculate potential energy savings
The web-based tool SinaSave can be used to estimate the potential savings which can be achieved over the entire lifecycle, e.g. for pump and fan applications, thanks to SINAMICS. The tool takes into consideration all important plant-specific quantities, such as the power and load data of the application, the relevant control mode and the operation profile for the application in question. The result delivered by the tool specifies the potential energy savings which can be achieved with the specific application in conjunction with the Integrated Drive System or the drive component. The tool also provides a monetary evaluation of the potential savings and estimates the payback period.
Drive Technology Configurator (DT Configurator) within the CA 01
The interactive catalog CA 01 – the offline Industry Mall of Siemens on DVD‑ROM – contains over 100 000 products with approximately 5 million possible drive system product variants. The Drive Technology Configurator (DT Configurator) has been developed to facilitate selection of the correct motor and/or converter from the wide spectrum of drives. It is integrated as a selection tool in Catalog CA 01.
Online DT Configurator
In addition, the DT Configurator can be used on the Internet without requiring any installation. The DT Configurator can be found in the Siemens Industry Mall at the following address:
http://www.siemens.com/dt-configurator
Configuring made simple and systematic
The SIZER for Siemens Drives engineering tool is used to configure low-voltage drive systems: Using the application as the prime reference, this tool provides step-by-step support in defining the mechanical system and designing converters, motors and gear units. It also helps the user to configure other system components and to design open-loop and closed-loop control functions. In addition to engineering results such as characteristics, technical specifications and installation and dimensional drawings, SIZER for Siemens Drives also provides calculations pertaining to performance and load-dependent power requirements.
Drive engineering – flexible, customized and user-friendly
A solution for a drive task can be identified quickly with the web-based tool: menu-prompted workflows guide the user through the technical selection and dimensioning of products and drive systems, including the accessories.
Based on an integrated inquiry functionality, SIZER WEB ENGINEERING also offers you special customized solutions for applications which cannot be addressed using “Standard Products”; i.e. the focus is on flexibility and customized solutions.
Comprehensive documentation, such as data sheets, startup calculations, dimensional drawings, offer documentation and a lot more are integrated in the tool. The result: Customized solutions for any drive task.
The product groups supported are:
The tool can also be used to design the following drive systems:
Commissioning and diagnostics – intelligent and easy
The STARTER commissioning tool allows menu-prompted commissioning, optimization and diagnostics. Apart from the SINAMICS drives, STARTER is also suitable for MICROMASTER 4 devices.
SINAMICS engineering in the TIA Portal
SINAMICS Startdrive is a tool for configuring, commissioning, and diagnosing the SINAMICS family of drives and is integrated into the TIA Portal. SINAMICS Startdrive can be used to implement drive tasks with the SINAMICS G120, SINAMICS G120C, SINAMICS G110M, SINAMICS G120D and SINAMICS G120P drives. The commissioning tool has been optimized with regard to user-friendliness and consistent use of the TIA Portal benefits of a common working environment for PLC, HMI and drives.
Drive ES is the engineering system that can be used to integrate the communication, configuration and data management functions of Siemens drive technology into the SIMATIC automation world easily, efficiently and cost-effectively. Two software packages are available for SINAMICS – Drive ES Basic and Drive ES PCS 7.
You can find more information about the Drive ES engineering system in the chapter Engineering Tools.
Additional information about the Drive ES engineering system is available on the internet at
http://www.siemens.com/drive-es
Unless explicitly specified otherwise, the following technical specifications are valid for all the following components of the SINAMICS G120P and SINAMICS G120P Cabinet pump, fan, compressor converters.
SINAMICS G120P | |
---|---|
Mechanical specifications | |
Vibratory load | |
Storage acc. to EN 60721‑3‑1 | |
Drives and components, frame sizes FSA to FSF | Class 1M2Deflection: 1.5 mm at 5 … 9 Hz Acceleration: 0.5 × g at 9 … 200 Hz |
Drives and components, frame sizes GX to JX | Class 1M2Deflection: 1.5 mm at 5 … 9 Hz Acceleration: 0.5 × g at 9 … 200 Hz |
SINAMICS G120P Cabinet | Class 1M2Deflection: 1.5 mm at 5 … 9 Hz Acceleration: 0.5 × g at 9 … 200 Hz |
Transport 1) acc. to EN 60721-3-2 | |
Drives and components, frame sizes FSA to FSC 2) | Class 2M2 |
Drives and components, frame sizes FSD to FSF 2) | Class 2M3 |
Drives and components, frame sizes GX to JX | Test FC according to EN 60068‑2‑6Deflection: ±1.5 mm at 5 … 9 Hz Acceleration: 0.5 × g at 9 … 200 Hz |
SINAMICS G120P Cabinet | Class 2M2 |
Operation acc. to EN 60721‑3‑3 | |
Drives and components, frame sizes FSA to FSF | Class 3M1 |
Drives and components, frame sizes GX to JX | Test FC according to EN 60068‑2‑6Deflection: 0.075 mm at 10 … 58 Hz Acceleration:10 m/s2 (1 × g) at 58 … 200 Hz |
SINAMICS G120P Cabinet | Class 3M2 |
Shock load | |
Storage acc. to EN 60721‑3‑1 | |
Drives and components, frame sizes FSA to FSF | Class 1M2 |
Drives and components, frame sizes GX and JX | Test FC according to EN 60068‑2‑6Deflection: ±1.5 mm at 5 … 9 Hz Acceleration: 0.5 × g at 9 … 200 Hz |
SINAMICS G120P Cabinet | Class 1M2Acceleration: 40 m/s2 (4 × g) at 22 ms |
Transport 1) acc. to EN 60721-3-2 | |
Drives and components, frame sizes FSA to FSC 2) | Class 2M2 |
Drives and components, frame sizes FSD to FSF 2) | Class 2M3 |
Drives and components, frame sizes GX to JX | Test FC according to EN 60068‑2‑6Deflection: ±1.5 mm at 5 … 9 Hz Acceleration: 0.5 × g at 9 … 200 Hz |
SINAMICS G120P Cabinet | Class 2M2 |
Operation acc. to EN 60721‑3‑3 | |
Drives and components, frame sizes FSA to FSC | Class 3M2 |
Drives and components, frame sizes FSD to FSF | Class 3M1 |
Drives and components, frame sizes GX and JX | Test Ea according to EN 60068‑2‑27Acceleration: 49 m/s2 (5 × g) at 30 ms or 147 m/s2 (15 × g) at 11 ms |
SINAMICS G120P Cabinet | Class 3M2 |
Ambient conditions | |
Protection classAccording to EN 61800‑5‑1 | Class I (with protective conductor system) and class III (PELV) |
Touch protection | According to EN 50274 and DGUV Regulation 3 when used for the intended purpose |
Permissible ambient and coolant temperature (air) during operation for line-side power components and Power Modules | |
Low overload (LO) | Frame sizes FSA to FSC: -10 … +40 °C (14 … 104 °F) without derating Frame sizes FSD to FSF (PM230): 0 … 40 °C (32 … 104 °F) without derating Frame sizes FSD to FSF (PM240P-2): -20 … +40 °C (-4 … +104 °F) without derating Frame sizes FSA to FSF: >40 … 60 °C (>104 … 140 °F) see derating characteristicsFrame size GX to JX: 0 … 45 °C (32 … 113 °F) without derating >45 … 55 °C (>113 … 131 °F) see derating characteristicsSINAMICS G120P Cabinet 0 … 40 °C (32 … 104 °F) without derating >40 … 50 °C (>104 … 122 °F) see derating characteristics |
High overload (HO) | Frame sizes FSA to FSC: -10 … +50 °C (14 … 122 °F) without derating Frame sizes FSD to FSF (PM230): 0 … 50 °C (32 … 122 °F) without derating Frame sizes FSD to FSF (PM240P-2): -20 … +50 °C (-4 … +122 °F) without derating >50 … 60 °C (>122 … 140 °F) see derating characteristicsFrame size GX to JX: 0 … 45 °C (32 … 113 °F) without derating >45 … 55 °C (>113 … 131 °F) see derating characteristicsSINAMICS G120P Cabinet 0 … 40 °C (32 … 104 °F) without derating >40 … 50 °C (>104 … 122 °F) see derating characteristics |
Installation altitude | Up to 1000 m (3281 ft) above sea level without derating, > 1000 m (3281 ft) see derating characteristics |
Permissible ambient and coolant temperature (air) during operation for Control Units and supplementary system components | With CU230P‑2 HVAC/DP with/without blanking cover: -10 … +60 °C (14 … 140 °F)With CU230P‑2 PN with/without blanking cover: -10 … +55 °C (14 … 131 °F)With IOP‑2/BOP‑2: 0 … 50 °C (32 … 122 °F)Derating of 3 K/1000 m applies to Control Units as of an installation altitude of 1000 m (3281 ft) above sea level. |
Climatic ambient conditions | |
Storage 1) acc. to EN 60721‑3‑1 | |
Drives and components, frame sizes FSA to FSF for PM230 | Temperature -40 … +70 °C (-40 … +158 °F) Relative air humidity <95 %, condensation not permissible |
Drives and components, frame sizes FSD to FSF for PM240P-2 | Class 1K3 Temperature -25 … +55 °C (-13 … +131 °F) Relative air humidity 5 … 95 %, condensation not permissible |
Drives and components, frame sizes GX to JX and SINAMICS G120P Cabinet | Class 1K4 Temperature -25 … +55 °C (-13 … +131 °F) Relative air humidity 5 … 95 %, condensation not permissible |
Transport 1) acc. to EN 60721-3-2 | |
Drives and components, frame sizes FSA to FSF | Class 2K4 Temperature -40 … +70 °C (-40 … +158 °F) Max. air humidity 95 % at 40 °C (104 °F) |
Drives and components, frame sizes GX to JX and SINAMICS G120P Cabinet | Class 2K3 Temperature -25 … +70 °C (-13 … +158 °F), -40 °C (104 °F) permissible for 24 h Relative air humidity 5 … 95 % at 40 °C (104 °F) |
Operation acc. to EN 60721‑3‑3 | |
Drives and components, frame sizes FSA to FSF | Class 3K3 Condensation, splashwater, and ice formation not permitted (EN 60204, Part 1) |
Drives and components, frame sizes GX to JX | Class 3K3 Temperature 0 … 45 °C (32 … 113 °F), up to 55 °C (131 °F) with derating Relative air humidity 5 … 95 % Condensation, splashwater and ice formation are not permitted (EN 60204, Part 1) |
SINAMICS G120P Cabinet | Class 3K3 Temperature 0 … 40 °C (32 … 104 °F), up to 50 °C (122 °F) with derating Relative air humidity 5 … 95 % Condensation, splashwater and ice formation are not permitted (EN 60204, Part 1) |
Environmental class/harmful chemical substances | |
Storage 1) acc. to EN 60721‑3‑1 | Class 1C2 |
Transport 1) acc. to EN 60721-3-2 | Class 2C2 |
Operation acc. to EN 60721‑3‑3 | Class 3C2 |
Organic/biological influences | |
Storage 1) acc. to EN 60721‑3‑1 | Class 1B1 |
Transport 1) acc. to EN 60721-3-2 | Class 2B1 |
Operation acc. to EN 60721‑3‑3 | Class 3B1 |
Degree of pollutionAccording to EN 61800‑5‑1 | 2 |
Standards | |
Compliance with standards | |
Drives and components, frame sizes FSA to FSF | UL, cUL 3), CE, RCM, SEMI F47 |
Drives, frame sizes GX to JX | cULus, CE, RCM, EAC, KC, SEMI F47 4) |
SINAMICS G120P Cabinet | CE, RCM, EAC, KC, SEMI F47 4) |
CE marking | According to Low Voltage Directive 2014/35/EU, EMC Directive 2014/30/EU |
EMC DirectiveAccording to EN 61800-3 | |
PM230: Frame sizes FSA to FSF with integrated line filter class A, degree of protection IP20/UL Open Type and IP55/UL Type 12 | The Power Modules comply with Category C2 according to EN 61800‑3. |
PM230: Frame sizes FSA to FSF with integrated line filter class B, degree of protection IP55/UL Type 12 | The Power Modules comply with the limit values for low-frequency line harmonics and conducted interference according to Category C1. They comply with the limit values for field-conducted interference emissions according to Category C2. |
PM240P-2: Frame sizes FSD to FSF (380 … 480 V 3 AC) with integrated line filter class A | The Power Modules comply with Category C2 according to EN 61800‑3. |
PM240P-2: Frame size FSF (500 … 690 V 3 AC) with integrated line filter class A | The Power Modules comply with Category C3 according to EN 61800‑3. |
PM330: Frame sizes GX to JX | Category C3 5) |
PM330: Frame sizes GX to JX with additional line filter class A | Category C2 6) |
SINAMICS G120P Cabinet | Category C3 7) |
SINAMICS G120P Cabinet with additional line filter class A | Category C2 7) |
Deviations from the specified classes are underlined.
1) In transport packaging.
2) In product packaging.
3) Applies to PM230 Power Modules frame sizes FSA to FSC and PM240P‑2 Power Modules with integrated line filter class A.
4) SEMI F47 for PM330 Power Modules, frame sizes HX (500 V to 690 V) and JX, available soon.
5) Standard configuration: Devices installed in the control cabinet with EMC-compatible configuration, line reactor uK = 2 %, shielded motor cable (e.g. Protoflex EMC) with max. 150 m cable length. Line harmonics acc. to EN 61000‑2‑4: Class 3, THD(U) total = 10 % for typical line conditions (RSC > 10);THD(I) total: typically 30 … 45 % (15 > RSC > 50).
6) Use in the second environment, for boundary conditions refer to 6).
7)For boundary conditions see 6), cabinet is configured accordingly in version A.
Note:
The EMC product standard EN 61800-3 does not apply directly to a frequency converter but to a PDS (Power Drive System), which comprises the complete circuitry, motor and cables in addition to the converter. The frequency converters on their own do not generally require identification according to the EMC Directive.
CE marking
The SINAMICS G120P and SINAMICS G120P Cabinet converters meet the requirements of the Low-Voltage Directive 2014/35/EC.
Low-Voltage Directive
The converters comply with the following standards listed in the official journal of the EU:
UL listing
Converters in UL category NMMS certified to UL and cUL, in compliance with UL508C or ULC61800‑5‑1. UL File Number E121068 and E192450.
For use in environments with pollution degree 2.
See also on the Internet at http://www.ul.com
Machinery directive
The converters are suitable for installation in machines. Compliance with the Machinery Directive 2006/42/EC requires a separate certificate of conformity. This must be provided by the plant construction company or the organization marketing the machine.
Functional safety
SINAMICS G120P and SINAMICS G120P Cabinet are not intended for use in installations with functional safety as defined by ISO 13849‑1, IEC 61508‑x.
EMC Directive
The following explanatory information applies to SINAMICS G120P and SINAMICS G120P Cabinet converters supplied by Siemens AG:
SEMI F47
SEMI F47 is an industry standard relating to the immunity to voltage dips. This includes the requirement that industrial equipment must be able to tolerate defined dips or drops of the line supply voltage. As a result, industrial equipment that fulfills this standard is more reliable and productive.
All Power Modules of the SINAMICS G120P product family fulfill the latest standard SEMI F47-0706 1). In the case of a voltage dip, defined in accordance with SEMI F47‑0706, these drives either continue to supply a defined output current, or using an automatic restart function, continue to operate as expected.
1) SEMI F47 for PM330 Power Modules, frame sizes HX (500 V to 690 V) and JX, available soon
EAC approval for Russia/Belarus/Kazakhstan/Armenia
Since 2013-02-15, Russia, Kazakhstan, Belarus and Armenia have been united in the Eurasian EAC customs union. An EAC approval as replacement for the GOST mark is required for all products that are to be sold in Russia.
All devices delivered to the customs union must have these customs certifications.
RCM approval for Australia
The RCM mark is required for marketing Siemens electronic devices in Australia. Electronic devices must provide proof of EMC clearance in Australia, similar to the CE marking of conformity laid down by the EMC directive applicable in the EU. The converters must be marked accordingly. These requirements have been in force since October 1, 1999.
On March 1, 2016, the C-Tick mark was replaced by the RCM mark.
KC approval for South Korea
KC approval (formerly KCC) is required for the distribution of our electrical equipment in South Korea. Electronic devices that are covered by the EU Directive on Electromagnetic Compatibility must provide an EMC certificate issued by a resident authority in South Korea. The converters must be marked accordingly. This requirement has been in force since January 24, 2011.
General technical specifications
Power Modules | PM230 | PM240P-2 | PM330 | Cabinet |
---|---|---|---|---|
System operating voltage | 380 … 480 V 3 AC ±10 % | 380 … 480 V 3 AC ±10 %500 … 690 V 3 AC ±10 % | 380 … 480 V 3 AC ±10 %500 … 690 V 3 AC ±10 % | 380 … 480 V 3 AC ±10 %500 … 690 V 3 AC ±10 % |
Grid requirement Short-circuit power RSC |
>100 | >25 | >33 line reactor recommended | >33 1) line reactors installed as standard |
Input frequency | 47 … 63 Hz | 47 … 63 Hz | 47 … 63 Hz | 47 … 63 Hz |
Output frequency | ||||
Control mode U/f | 0 … 550 Hz | 0 … 550 Hz | 0 … 150 Hz | 0 … 150 Hz |
Control type Vector | 0 … 240 Hz | 0 … 200 Hz | 0 … 150 Hz | 0 … 150 Hz |
Pulse frequency | 4 kHzHigher pulse frequencies up to 16 kHz, see derating data | At 380 … 480 V 3 AC: Up to 90 kW LO: 4 kHz From 110 kW LO: 2 kHzHigher pulse frequencies up to 16 kHz, see derating dataAt 500 … 690 V 3 AC: 2 kHz, can be adjusted to 4 kHz |
Self-adjusting up to 4 kHz | Self-adjusting up to 4 kHz |
Power factor λ | 0.9 | 0.9 … 0.95 | 0.75 … 0.93 | 0.75 … 0.93 |
Offset factor cos φ | 0.95 | 0.99 | 0.96 | 0.96 |
Efficiency | ≤97 % | >97 % | >98 % | >98 % |
Output voltage, max.In % of input voltage | 95 % | 95 % | 97 % | 97 % |
Overload capability | ||||
Low overload (LO) Note:When the overload capability is used, the base-load current IL is not reduced. |
FSA to FSC: 1.5 × base-load current IL (i. e. 150 % overload) for 3 s plus 1.1 × base-load current IL (i. e. 110 % overload) for 57 s within a cycle time of 300 sFSD to FSF: 1.1 × base-load current IL (i.e. 110 % overload) for 60 s within a cycle time of 300 s |
1.35 × base-load current IL (i.e. 135 % overload) for 3 s plus 1.1 × base-load current IL (i.e. 110 % overload) for 57 s within a cycle time of 300 s | 1.35 × base-load current IL (i.e. 135 % overload) for 3 s or1.1 × base-load current IL (i.e. 110 % overload) for 60 s within a cycle time of 300 s | 1.35 × base-load current IL (i.e. 135 % overload) for 3 s or1.1 × base-load current IL (i.e. 110 % overload) for 60 s within a cycle time of 300 s |
High overload (HO) Note:When the overload capability is used, the base-load current IH is not reduced. |
FSA to FSC: 2 × base-load current IH (i. e. 200 % overload) for 3 s plus 1.5 × base-load current IH (i. e. 150 % overload) for 57 s within a cycle time of 300 sFSD to FSF: 1.5 × base-load current IH (i.e. 150 % overload) for 60 s within a cycle time of 300 s |
1.5 × base-load current IH (i. e. 150 % overload) for 60 s within a cycle time of 300 s | 1.5 × base-load current IH (i. e. 150 % overload) for 60 s within a cycle time of 300 s | 1.5 × base-load current IH (i. e. 150 % overload) for 60 s within a cycle time of 300 s |
Possible braking methods | DC braking | DC brakingCompound braking | DC brakingDynamic braking with optional Braking Module | DC brakingDynamic braking with optional Braking Module |
Overvoltage category acc. to IEC 61800‑5‑1 | III | III | Supply circuits: III Non-supply circuits: II |
III |
Degree of protection | IP55/UL Type 12 (with IOP‑2, BOP‑2 or blanking cover)IP20 (Standard or Push Through) | IP20 | IP20 | Standard: IP20Optional: IP21, IP23, IP43 and IP54 |
Cooling | Power units with increased air cooling using integrated fans | Internal air cooling, power units with increased air cooling by built-in fans | Internal air cooling, power units with increased air cooling by built-in fans | Internal air cooling, power units with increased air cooling by built-in fans |
Protection functions | UndervoltageOvervoltageOvercurrent/overloadOvertemperatureGround faultShort-circuitStall protectionMotor blocking protectionMotor overtemperatureParameter locking | |||
Short-Circuit Current Rating SCCRacc. to UL(Short-Circuit Current Rating) 2) | Degree of protection IP55 frame sizes FSA to FSC: 40 kADegree of protection IP55 frame sizes FSD to FSF and degree of protection IP20: 65 kA | 100 kA | 100 kA 3) | – |
Short-Circuit Current Rating ICCacc. to IEC 3) | – | 100 kA | 100 kA 3) | 65 kA 3) |
1) Does not apply in conjunction with option L01.
2) Applies to industrial control panel installations according to NEC Article 409 or UL 508A/508C or UL 61800-5-1.
3) In combination with the fuses specified in section Recommended line-side overcurrent protection devices and/or Load-side power components.
Shield connection kit 1 for CU230P‑2 HVAC/DP Control Units
Shield connection kit 1 offers optimum shield connection and strain relief for all signal and communication cables. It includes a matching shield connection plate and all of the necessary connecting and retaining elements for mounting.
Shield connection kit 3 for CU230P‑2 PN, CU240E‑2 PN and CU240E‑2 PN‑F Control Units
Shield connection kit 3 offers optimum shield connection and strain relief for all signal and communication cables. It includes a matching shield connection plate and all of the necessary connecting and retaining elements for mounting.
SINAMICS memory card (SD card)
The parameter settings for a converter can be stored on the SINAMICS SD memory card. The SINAMICS SD card can be used to pre-parameterize converters and to clone complete converter data sets. When service is required, e.g. after the converter has been replaced and the data have been downloaded from the memory card the drive system is immediately ready for use again. The associated slot is located on the top of the Control Unit.
PC converter connection kit 2
For controlling and commissioning the converter directly from a PC, if the STARTER commissioning tool has been installed on the PC.
Installation kit for line-side cable connection, left, for PM330 Power Modules
This installation kit allows supply cables to be brought in from the left-hand side of frame size GX and HX PM330 Power Modules. It is then possible to install the Power Module in the cabinet without any clearance at the top.
Mounting set for PM230 and PM240P-2 Power Modules
Depending on the frame size, different mounting sets are available for PM230 and PM240P-2 Power Modules.
Fan units for PM230 Power Modules
The PM230 Power Module is equipped with an internal and an external fan unit. Both of these can be replaced if necessary.
Replacement fans
The fans for PM240P-2 and PM330 Power Modules are available to order as replacement fans.
Did you know, we are an entrusted Siemens approved partner?
All goods supplied by us are sold upon the following conditions. This agreement applies as between you, the User of this Web Site or Purchaser and Parmley Graham Limited the owner(s) of this Web Site. Your agreement to comply with and be bound by these Terms and Conditions is deemed to occur upon your first use of the Web Site. If you do not agree to be bound by these Terms and Conditions, you should stop using the Web Site immediately. No part of this Web Site is intended to constitute a contractual offer capable of acceptance. The Purchaser's order constitutes a contractual offer and our acceptance of that offer is deemed to occur upon our sending an email to the Purchaser indicating that the order has been accepted for processing. Unless expressly agreed by us in writing, any other terms or conditions, including any which may be contained in your orders, are excluded. Unless expressly incorporated in our quotation or tender, all descriptions, illustrations, drawings, dimensions, weights, measures, specifications, standards of performance or other descriptive matter of precontractual statement are approximate only and shall not form part of the contract.
These Terms and Conditions apply to business customers only.
If Goods are being ordered from outside Parmley Graham Limited's country of residence, import duties and taxes may be incurred once the Goods reach their destination. Parmley Graham Limited is not responsible for these charges and we undertake to make no calculations or estimates in this regard. If a Purchaser is buying internationally, they are advised to contact their local customs authorities for further details on costs and procedures. The Purchaser of the Goods will also be the importer of record and as such should ensure that the purchase is in full compliance with the laws of the country into which the Goods are being imported. Please be aware that Goods may be inspected on arrival at port for customs purposes and Parmley Graham Limited gives no guarantee that the packaging of the Goods will be free of signs of tampering.
Any such order placed via our website will be considered to be an “Invitation to Treat” and any payment made as a refundable deposit, until such time as the order is reviewed and confirmed. During our contract review we are legally obliged to take into account any Export Restrictions, Sanctions or Embargoes in force at the time from the UK Government, European Union or UN ( US export regulations may also apply to some products) and such restrictions may prevent supply of the goods. In some cases we may require End-User details and/or Dual Use WMD statements prior to supply. Should an Export License be required, or additional documentation including Certificates of Origin, it may be necessary to apply additional costs.
In order to purchase Goods on this Web Site and to use the other facilities Users are required to create an Account which will contain certain personal details and Payment Information which may vary based upon a User's use of the Web Site as we may not require payment information until a purchase is to be made. By continuing to use this Web Site you represent and warrant that:
All information you submit is accurate and truthful;
If you are buying on behalf of your employers, you have the authority to submit Payment Information where any such authority is required; and
You will keep this information accurate and up-to-date. Your creation of an Account is further affirmation of your representation and warranty.
It is recommended that you do not share your Account details, particularly your username and password. Parmley Graham Limited accepts no liability for any losses or damages incurred as a result of your Account details being shared by you. If you use a shared computer, it is recommended that you do not save your Account details in your internet browser. If you have reason to believe that your Account details have been obtained by another without consent, you should contact Parmley Graham Limited immediately to suspend your Account and cancel any unauthorised purchases that may be pending. Please be aware that purchases can only be cancelled until they are dispatched. In the event that an unauthorised purchase is dispatched prior to your notifying us of the unauthorised nature of the purchase, Parmley Graham Limited accepts no liability or responsibility and you should make contact with the Carrier detailed in the Purchase Information.
All goods are sold subject to the prices ruling at the date of despatch.
The price of the Goods shall be subject to the addition of the applicable delivery prices as indicated on the Web Site, Value Added Tax and other applicable taxes and the cost of any special packing required by the Customer.
A small order charge may be applied to orders less than £25 (ex VAT).
Payment must be made by the 28th day of the month subsequent to the month following delivery on a "Strictly Net" basis. We shall be entitled to charge interest on overdue accounts at the rate of 1.5% per month. (b) Where the contract is to be or may be fulfilled in separate installments deliveries or parts, payment for each such installment, delivery or part shall be made as if the same constituted a separate contract.
The risk in all goods passes to you when they first enter the premises stipulated on the order. We reserve the right to choose the method of transport, to charge for deliveries, and charge you with manufacturers' carriage charges for special items.
The Company may deliver the Goods in instalments and invoice the Customer as if each instalment comprised a separate Contract upon the terms of these Conditions.
Notification of any shortage or damage must be received at our branch within seven days after the date of delivery; otherwise no claim will be entertained. Written notice of any non delivery must be received at our branch within seven days after the date of invoice. Time is of the essence of this clause. Our liability in respect of any claim accepted under this clause is limited to making up the shortage or replacing any goods proven to have been damaged or lost in transit to the point of delivery, and we accept no liability for any loss or damage suffered by you whether direct or consequential and howsoever arising.
Any delivery dates quoted by the Company are approximate only and will not form part of the contract. Stock indications are provided on the Web Site; however these may not take into account sales that have taken place during your visit to the web site. If the customer fails for whatever reason to take delivery of the goods on the due date the Company will be entitled to store the goods and then risk in the goods will pass to the customer, delivery will be deemed to have taken place and the customer will pay all costs and expenses including storage and insurance charges arising from its failure.
Notwithstanding delivery, all goods supplied by us will remain our absolute property until you pay in full for them and for all other goods previously supplied by us. You will store the goods in such a way that they are readily identifiable as our property, but you may, as trustees for us, sell them to a third party in the normal course of your business. Upon any sale by you of the goods (either alone or with other items) all rights which you have against the buyer shall automatically vest in us. We shall be entitled immediately after giving notice of our intention to repossess, to enter upon any premises with such transport as may be necessary and repossess any goods to which we have title under this clause.
It is your responsibility to determine that the goods are sufficient and suitable for the purpose to which they are to be put. We cannot accept any responsibility either in respect of the installation of any goods or as to the ultimate performance of any product in which the goods may be installed. We shall in no way be liable for any direct or consequential damage, loss or expense arising from any defect or inefficiency caused by the manner in which the goods are used.
All goods supplied by us are manufactured by others. Accordingly, we shall pass on to you the benefit of the warranty, if any, given by the manufacturer of the goods. Our liability under this clause shall be in lieu of any warranty or condition implied by law as to the quality or fitness for any particular purpose of the goods, and we shall not be under any liability, whether in contract, tort or otherwise, in respect of any defects in goods delivered or for any injury, damage or loss resulting from such defects or from anything done or omitted in connection with the goods or from any work done in connection therewith.
In no circumstances may goods supplied against a firm order be returned without our prior written consent and the receipt of your advice note stating the reason for return and date and number of our invoice. All goods returned must be securely packed and consigned carriage paid. In all cases we reserve the right to make a handling charge, and the issue of our goods received note will not bind us to issue any credit in respect of the goods.
We may, without prejudice to our other rights and remedies determine the contract or any unfulfilled part of it or withhold further deliveries or make partial deliveries if: (a) You fail to make payment on the due date under this or any other contract between us. (b) You purport to cancel or suspend, or commit any breach of this or any other contract between us. (c) You become insolvent, or make any composition with your creditors or have a receiver appointed of all or any part of your undertaking or assets or go into liquidation (save for the purposes of amalgamation or reconstruction) and we shall be entitled to recover from you all our loss including any loss of profit or loss on resale.
Any failure by us to enforce any of all these Conditions shall not be construed as a waiver of any of our rights hereunder.
The information contained in this website is for general information purposes only. The information is provided by Parmley Graham Limited and whilst we endeavour to keep the information up-to-date and correct, we make no representations or warranties of any kind, express or implied, about the completeness, accuracy, reliability, suitability or availability with respect to the website or the information, products, services, or related graphics contained on the website for any purpose. Any reliance you place on such information is therefore strictly at your own risk.
In no event will we be liable for any loss or damage including without limitation, indirect or consequential loss or damage, or any loss or damage whatsoever arising from loss of data or profits arising out of or in connection with the use of this website
Every effort is made to keep the website up and running smoothly. However, Parmley Graham Limited takes no responsibility for and will not be liable for the website being temporarily unavailable due to technical issues beyond our control.
Data controller: Parmley Graham Limited,
South Shore Road, Gateshead, Tyne and Wear, NE8 3AE
Parmley Graham Limited collects and processes your personal data when you interact with us. For the purposes of this Privacy Policy, references to “we”, “us” or “the organisation” shall refer to Parmley Graham Limited. The organisation is the data controller of your personal data and is responsible for complying with data protection laws. The organisation is committed to being transparent about how it collects and uses that data and to meeting its data protection obligations.
This notice applies to all suppliers, customers and other parties who utilise the services of Parmley Graham Limited.
By providing your personal data, you acknowledge that we may use it only in the ways set out in this Privacy Policy.
From time to time we may need to make changes to this Privacy Policy, for example as the result of government regulation, new technologies, or other developments in data protection laws or privacy generally and will provide you with a new privacy notice when we make substantial updates.
Our privacy principles
When we collect and use your personal data, we ensure we look after it properly and use it in accordance with our privacy principles below whereby the personal information we hold about you must be:
· processed fairly and lawfully and in a transparent way;
· obtained only for specific, lawful purposes;
· adequate, relevant and not excessive;
· accurate and kept up to date;
· not held for any longer than necessary;
· processed in accordance with the rights of data subjects;
· protected in appropriate ways;
· not be transferred outside the European Economic Area (EEA), unless where necessary and that country or territory also ensures an adequate level of protection.
What personal data do we collect?
We collect and process a range of data about you. This may include:
· contact details such as name, email address, postal address and telephone number;
· financial information and information about the nature of your business, such as bank details, credit card details and information obtained as a result of our credit checks;
· details of your interactions with us through our branches or online;
· information about the nature of your business and commercial assets;
· your image may be recorded on CCTV when you visit a Parmley Graham site;
· information obtained through our use of cookies. You can find out more about this in our cookies policy; and
· your marketing preferences.
How do we collect your personal data?
We collect, store and process personal data directly from you:
· via enquiry;
· when you create an account with us;
· when you purchase any of our products or services;
· through quotes;
· via our telephone calls with you;
· via emails;
· when you provide your details to us either online or offline;
· when you engage with us on social media;
How do we use your personal data?
We mainly use your personal data to provide you with goods and services. There are a number of other reasons we use your personal data, as explained in the list below.
In specific situations we require your data to pursue our legitimate interests in a way which might reasonably be expected as part of running our business, whilst ensuring that such business needs do not interfere with your rights and freedoms and do not cause you any harm. Where we list legitimate interests as a reason, we also describe below what we believe these legitimate interests are.
In specific situations, we can collect and process your data with your consent. We will usually only ask for your consent when providing marketing information to you, including information about other products and services. This will be made clear when you provide your personal information. If we ask for your consent we will explain why it is necessary.
What we use your personal data for |
Our reasons (legal basis) |
Explanation of our legitimate interests |
Set up your customer account |
Legitimate interest |
Process efficiency in dealing with such activity |
Provide you with quotes |
Legitimate interest |
Process efficiency in dealing with such activity |
Process your order, to supply you with goods and services |
Contractual obligation |
Fulfil the contract |
Notify you of your order status |
Legitimate interest |
Process efficiency in dealing with such activity |
Manage your account |
Legitimate interest |
Maintaining our business records |
Detect, investigate and report financial crime (eg Fraud) |
Legal compliance |
NA |
Undertake marketing communication, to inform you about other products and services |
Legitimate interest |
To keep subscribed customers up to date with information on related services and products. |
The use of CCTV to record images for security. |
Legitimate interest |
To protect our customers, premises, assets and employees from crime |
Who has access to the data?
Your information may be shared internally within the organisation, including with the Directors, members of the HQ finance team, IT staff and branch employees if access to the data is necessary for performance of their roles.
Also, we may sometimes share your data with trusted third parties that process the data on our behalf. We share only the personal information they need to perform their specific services and they may only use your data for the reasons we’ve described.
We work closely with the third party data processors to ensure your privacy is respected and protected at all times.
How do we protect the data?
The organisation takes the security of your data seriously. We have internal policies and controls in place to try to ensure that your data is not lost, accidentally destroyed, misused or disclosed, and is not accessed except by its employees in the performance of their duties.
We secure access to our systems and access to your personal data is password protected.
We regularly monitor our system for possible vulnerabilities and attacks, and we carry out penetration testing to identify ways to further strengthen security.
We work closely with the third party data processors to ensure your privacy is respected and protected at all times.
For how long do we keep the data?
We will only retain your personal data for as long as is necessary to fulfil the purposes for which it is collected.
When assessing what retention period is appropriate for your personal data, we take into consideration:
· the requirements of our business and the services provided;
· any statutory or legal obligations;
· the purposes for which we originally collected the personal data;
· the lawful grounds on which we based our processing;
· the types of personal data we have collected;
· the amount and categories of your personal data; and
· whether the purpose of the processing could reasonably be fulfilled by other means.
Your duty to inform us of changes
It is important that the personal information we hold about you is accurate and current. Please keep us informed if your personal information changes during your working relationship with us.
Your rights / contacting the regulator
As a data subject, you have the following rights in relation to our use of your personal data:
- The right to access your personal data
You are entitled to a copy of the personal data we hold about you and certain details of how we use it
- The right to rectification
We take reasonable steps to ensure that the personal information we hold about you is accurate and complete. However, if you do not believe this is the case, please contact us by using the details shown in your documentation and you can ask us to update or amend it.
- The right to erasure
In certain circumstances, you have the right to ask us to erase your personal information, for example where the personal information we collected is no longer necessary for the original purpose or where you withdraw your consent. However, this will need to be balanced against other factors, for example according to the type of personal information we hold about you and why we have collected it, there may be some legal and regulatory obligations which mean we cannot comply with your request.
- The right to restriction of processing
In certain circumstances, you are entitled to ask us to stop using your personal information, for example where you think that the personal information we hold about you may be inaccurate or where you think that we no longer need to process your personal information.
- The right to data portability
In certain circumstances, you have the right to ask that we transfer any personal information that you have provided to us to another third party of your choice. Once transferred, the other party will be responsible for looking after your personal information.
- The right to object to direct marketing
You can ask us to stop sending you marketing messages at any time. Please see the Marketing section at the end of this page for more information.
- The right not to be subject to automated decision-making
We do not use automated decision-making
- The right to withdraw consent
For certain uses of your personal information, we will ask for your consent. Where we do this, you have the right to withdraw your consent to further use of your personal information.
If you would like to exercise any of these rights, please contact email: privacy@parmley-graham.co.uk, address: Parmley Graham Ltd, South Shore Road, Gateshead, Tyne and Wear, NE8 3AE.
If we choose not to action your request we will explain to you the reasons for our refusal.
If you feel that your data has not been handled correctly, or you are unhappy with our response to any requests you have made to us regarding the use of your personal data, you have the right to lodge a complaint with the Information Commissioner’s Office.
You can contact them by calling 0303 123 1113.
Or go online to https://ico.org.uk/make-a-complaint/ (opens in a new window; please note we can't be responsible for the content of external websites)
If you are based outside the UK, you have the right to lodge your complaint with the relevant data protection regulator in your country of residence.
Marketing
We are committed to only sending you marketing communications that you have clearly expressed an interest in receiving. If you wish to unsubscribe from emails sent by us, you may do so at any time by following the unsubscribe instructions that appear in all emails or by sending an email, from the email address you wish to have unsubscribed, to unsubscribe@parmley-graham.co.uk.
Date of last review: 19/05/2023